Index of Classic Heroscape .stl files

[White Knight]

Originally Posted by Amarant

This is such an excellent resource, thank you for providing it. Are there any plans to do matte scans of the other four Aquilla's Alliance figures.

Yes. Right now I think I have photographs of every classic figure (including the flag bearers) except for Zelrig.

[White Knight]

Originally Posted by Guillermo-Tell

About the glass bed, I have one and always use it. The main pro is the completely flat surface you get at the bottom, but the main con is it's very difficult to make the prints attach to it. I found it's easier if you spread a thin layer of glue with a glue stick, but not too much or you can't remove the prints later!

I never have problems sticking to my glass bed, at least for miniatures. I just have the nozzle start really close to the bed.


My glass bed is slightly warped, so every now and then I'll have an issue on large pieces.

[Alexandros]

Originally Posted by White Knight

Yes. Right now I think I have photographs of every classic figure (including the flag bearers) except for Zelrig.

I think I might be miscommunciating, it looks like Wo-Sa-Ga is a higher quality than the other four AA figures . A friend of mine is printing them for me on his Elegoo Mars and expressed concerns about the quality they would print at?

[robbdaman]

Originally Posted by Amarant

I think I might be miscommunciating, it looks like Wo-Sa-Ga is a higher quality than the other four AA figures . A friend of mine is printing them for me on his Elegoo Mars and expressed concerns about the quality they would print at?

Wo-Sa-Ga was probably 3D sculpted, not scanned. Some of the other scans are pretty low resolution. I’m sure higher resolution scans will get done at some point.

[TREX]

Originally Posted by robbdaman

Wo-Sa-Ga was probably 3D sculpted, not scanned. Some of the other scans are pretty low resolution. I’m sure higher resolution scans will get done at some point.

The latest Wo Sa Ga model was sculpted by a member, not a scan. Its close, but not exact. But that is why it looks more clean.

[White Knight]

Originally Posted by Amarant

I think I might be miscommunciating, it looks like Wo-Sa-Ga is a higher quality than the other four AA figures . A friend of mine is printing them for me on his Elegoo Mars and expressed concerns about the quality they would print at?

No, I'm the one mis-communicating.


1) First, others are correct, Wo-Sa-Ga was sculpted by a @avoman and is cleaner than any of the scans, even the matte scans


2) There are no matte scans of Gurei-Oni, Sujoah, Zelrig, or Zetacron. Not yet.


3) To make a matte scan model, I first need to get good photographs of the figures. Then I run them through a computer program that converts the photos to 3D models. A fellow scaper recently lent me several of his Aquilla's Alliance figures, so I now have photographs of Gurei-Oni, Sujoah, and Zetacron. Soon I will run them through the program and upload the high resolution 3D matte models to this thread.


4) I do not have access to a Zelrig figure, so I do not have photographs yet to turn into a 3D matte model.

[Alexandros]

That really clears things up and I appreciate the time took took to explain - I'm very new to the world of 3D printing. Eagerly awaiting those uploads

[robbdaman]

The further adventures in 3D printing continue.





Bed leveling concerns kept giving me problems, lots of stringiness and incomplete prints. Then once I adjusted for closer and it seemed good my belt started skipping. Resulting in a not very cubicle cube. It was very solid printing though.



Reran the bed level test yet again and still got some skipping with those extra lines.



Adjusted a tiny bit more and tested a empty cube which skipped once to the side but successfully built the outside after that.



Gonna see about tightening the belt and trying more. I burned through the small filament that came with the printer and put on a SainSmart PRO-3 Tangle-Free Premium 1.75mm PLA spool.

[JairEmia]

Who uploaded the Wo-sa-ga? I am guessing someone modeled that? looks too perfect to be a scan. Any chance whoever it was wants to give Zelrig a similar makeover? He can't really be found anymore and when he can its like $150

[robbdaman]

Figured out what I was doing wrong. Learning curve. Feel free to ignore my questions, it makes me figure it out.

[Sir Heroscape]

Not sure this is the place to ask, but since this is where files for 3D printing bases are I was wondering if anyone also had a print file for the grassy “stickers” To go on the bases. I’d prefer a file that doesn’t waste the ink on the edges, but if that’s not possible,That’s okay

[Tornado]

Could you just scan a single grass tile?
If so, you could put multiple singles on the scanner to create a 'sheet of stickers'.