|
3D Printing A Forum to discuss 3D Printing |
|
Thread Tools | Search this Thread | Display Modes |
#49
|
||||
|
||||
Re: C3V/SoV 3D Printable Proxies
I'm so sorry - I'm sure we discussed "textured" models for TTS before. Is that possible?
|
#50
|
||||
|
||||
Re: C3V/SoV 3D Printable Proxies
Quote:
|
#51
|
||||
|
||||
Re: C3V/SoV 3D Printable Proxies
Understood!
|
#52
|
||||
|
||||
Re: C3V/SoV 3D Printable Proxies
Quote:
|
#53
|
||||
|
||||
Re: C3V/SoV 3D Printable Proxies
Set of lower resolution C3V scans (mostly in Blender)
Higher resolution C3V scans These files need cleanup before printing. SCALE @TREX As for scale, the scale is not absolute--it depends on where the camera is placed relative to the figures. Many of the C3V figures and the D1-D3 figures have non-standard base sizes. Here are the correct base sizes for various figures so that the figure can be scaled correctly: Figure: Diameter (in inches) D1-D3 D&D figures: 1.00" Gorilla Troopers: 1.558" Heroclix (Soldier and others): 1.360" Quahon (outside toe to outside toe wide): 2.1" Skull demon (Skeletons, Nhih Scrihr, Cathar): 1.190" Varkaanan Wolves: 1.565" Agaumo: 1.9" Zettian Deathwings (across the flats): .987" Zombie Hulk: 1.9" Major J15: 2.0" Project Pokemon, Kanto Pokemon (151) Star Wars Custom Army Cards LEGENDS OF 'SCAPE (RPG) Rulebook Templates Last edited by White Knight; January 9th, 2021 at 12:15 PM. |
#54
|
||||
|
||||
Re: C3V/SoV 3D Printable Proxies
Some Havech Eradicators I scanned:
Havech Eradicator scan 1 Havech Eradicator scan 2 Havech Eradicator scan 3 Havech Eradicator scan 4 Havech Eradicator bases |
#55
|
||||
|
||||
Re: C3V/SoV 3D Printable Proxies
Here are a few of WK's Scans that I fixed and scaled.
Arashara Goshiri Beorn Boltcutter Bramcephys These are all to scale exactly. I have all these figures and was able to measure them to the exact, then scaled accordingly. If printing in Resin, Bramcephys will need to be cut into pieces for all smaller build plates. I am planning on keying his arms. Check out my ebay where you can find my custom dice trays and dicetowers: https://www.ebay.com/usr/captainamazing_jerdo |
#56
|
|||
|
|||
Re: C3V/SoV 3D Printable Proxies
Thank you White Knight ! I can't wait to print some new guys on my cr6-se ! (if you have some Marro gnids it would be awesome )
|
#57
|
||||
|
||||
Re: C3V/SoV 3D Printable Proxies
The Gnids are in the directory I posted. They just need a little processing.
|
#58
|
||||
|
||||
Re: C3V/SoV 3D Printable Proxies
Quote:
|
#59
|
||||
|
||||
Re: C3V/SoV 3D Printable Proxies
Quote:
|
#60
|
||||
|
||||
Re: C3V/SoV 3D Printable Proxies
Quote:
Many of the C3V figures and the D1-D3 figures have non-standard base sizes. Here are the correct base sizes for various figures so that the figure can be scaled correctly: Figure: Diameter (in inches) D1-D3 D&D figures: 1.00" Gorilla Troopers: 1.558" Heroclix (Soldier and others): 1.360" Quahon (outside toe to outside toe wide): 2.1" Skull demon (Skeletons, Nhih Scrihr, Cathar): 1.190" Varkaanan Wolves: 1.565" Agaumo: 1.9" Zettian Deathwings (across the flats): .987" Zombie Hulk: 1.9" Major J15: 2.0" For ones not listed, look for ones from the same company. For example, the Varkaanan are from Confrontation. So are the Cathar Spearmen. So the base sizes are the same. If you have a specific figure you are unsure about, post it here and I'll try to give more exact information. I don't have all the figures, which is why I measured the bases before returning them to their owner. |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Printable Proxies | samthegoat | Other Customization & HS Additions | 6 | February 9th, 2016 01:15 PM |
If you need a quinjet (also a helicarrier printable mat) | omael | Marvel Maps & Scenarios | 12 | August 25th, 2014 12:26 PM |
looking for a printable/portable map | omael | Maps & Scenarios | 2 | May 10th, 2012 04:16 PM |
Printable terrain | polarcow | Other Customization & HS Additions | 3 | April 12th, 2011 09:25 AM |
Printable Battle Mats? | Sobriquet | Custom Terrain & Obstacles | 19 | March 17th, 2009 06:23 PM |