Welcome to the Heroscapers 2.0 site! We've still got some dust to clear and adjustments to make, including launching a new front page, but we hope you enjoy the improvements to the site. Please post your feedback and any issues you encounter in this thread.
Hey all,
I've done some research and I'm close to pulling the trigger on an AnyCubic Photon Mono SE Printer with the Wash and Cure Machine 2.0. I can get this + 1KG of plant based resin for $371. I'm wondering if anyone has experience purchasing resin printers and if so whether this is a good deal or not. I'm in no rush, so if better deals often come available I'd be happy to wait. If I end up waiting 6 months to a year to plunge into 3D printing I'd be OK with that.
Anyways, I'm probably looking to buy this in the next week if nothing changes so I'd appreciate any advice you have
I’m still rocking my anycubic photon original printer. 1 bought it for 170 bucks on a sale, I’ve replaced the screen once for 30 bucks and have printed a few thousand minis. Generally I would recommend any of the anycubic printers up to and including the mono x. You can go bigger or more resolution but in most cases you wouldn’t need to in this hobby. I’ve printed so many minis that I’ve been on a hiatus for a bit because I was out of room to store them and had too many to keep up on painting. As far as resin goes, it’s brittle. More brittle than filament. To counter that you need to use stronger resins or mix in resins. I prefer sirayatech fast abs resin. It’s about three times stronger than the average stuff and costs a little more but worth it. For even more strength you could mix in some tenacious but that stuff is literally double the cost. I’ve cleaned my models in a simple larger Tupperware container filled with IPA with no problems for a few years now changing it out ever so often when it becomes too clouded.
I’m still rocking my anycubic photon original printer. 1 bought it for 170 bucks on a sale, I’ve replaced the screen once for 30 bucks and have printed a few thousand minis. Generally I would recommend any of the anycubic printers up to and including the mono x. You can go bigger or more resolution but in most cases you wouldn’t need to in this hobby. I’ve printed so many minis that I’ve been on a hiatus for a bit because I was out of room to store them and had too many to keep up on painting. As far as resin goes, it’s brittle. More brittle than filament. To counter that you need to use stronger resins or mix in resins. I prefer sirayatech fast abs resin. It’s about three times stronger than the average stuff and costs a little more but worth it. For even more strength you could mix in some tenacious but that stuff is literally double the cost. I’ve cleaned my models in a simple larger Tupperware container filled with IPA with no problems for a few years now changing it out ever so often when it becomes too clouded.
Thanks a ton for the advice! After doing more research it looks like I'll have to move out of a dorm room before I'm able to get a printer due to the fumes. But this was helpful nonetheless!
I’m still rocking my anycubic photon original printer. 1 bought it for 170 bucks on a sale, I’ve replaced the screen once for 30 bucks and have printed a few thousand minis. Generally I would recommend any of the anycubic printers up to and including the mono x. You can go bigger or more resolution but in most cases you wouldn’t need to in this hobby. I’ve printed so many minis that I’ve been on a hiatus for a bit because I was out of room to store them and had too many to keep up on painting. As far as resin goes, it’s brittle. More brittle than filament. To counter that you need to use stronger resins or mix in resins. I prefer sirayatech fast abs resin. It’s about three times stronger than the average stuff and costs a little more but worth it. For even more strength you could mix in some tenacious but that stuff is literally double the cost. I’ve cleaned my models in a simple larger Tupperware container filled with IPA with no problems for a few years now changing it out ever so often when it becomes too clouded.
Thanks a ton for the advice! After doing more research it looks like I'll have to move out of a dorm room before I'm able to get a printer due to the fumes. But this was helpful nonetheless!
Did you ever pull the trigger on this? With the Heroscape revival on the horizon, I’m looking into resin printers for the sake rebuilding my collection after I had to sell in 2013.
I’m still rocking my anycubic photon original printer. 1 bought it for 170 bucks on a sale, I’ve replaced the screen once for 30 bucks and have printed a few thousand minis. Generally I would recommend any of the anycubic printers up to and including the mono x. You can go bigger or more resolution but in most cases you wouldn’t need to in this hobby. I’ve printed so many minis that I’ve been on a hiatus for a bit because I was out of room to store them and had too many to keep up on painting. As far as resin goes, it’s brittle. More brittle than filament. To counter that you need to use stronger resins or mix in resins. I prefer sirayatech fast abs resin. It’s about three times stronger than the average stuff and costs a little more but worth it. For even more strength you could mix in some tenacious but that stuff is literally double the cost. I’ve cleaned my models in a simple larger Tupperware container filled with IPA with no problems for a few years now changing it out ever so often when it becomes too clouded.
Thanks a ton for the advice! After doing more research it looks like I'll have to move out of a dorm room before I'm able to get a printer due to the fumes. But this was helpful nonetheless!
Did you ever pull the trigger on this? With the Heroscape revival on the horizon, I’m looking into resin printers for the sake rebuilding my collection after I had to sell in 2013.
I did, but I haven't gotten to use it yet. I live in a dorm so finding a spot I can safely set it up is a bit of a challenge. Resin is toxic, which means you don't want to run it in a living space - I think I just found a place I can use it but won't get around to the initial test till next week. Cost-wise, i found a used Anycubic Photon Mono SE for $100 and then I had to buy roughly another $100 of supplies (TREX sent me a list that was super helpful).
I’m still rocking my anycubic photon original printer. 1 bought it for 170 bucks on a sale, I’ve replaced the screen once for 30 bucks and have printed a few thousand minis. Generally I would recommend any of the anycubic printers up to and including the mono x. You can go bigger or more resolution but in most cases you wouldn’t need to in this hobby. I’ve printed so many minis that I’ve been on a hiatus for a bit because I was out of room to store them and had too many to keep up on painting. As far as resin goes, it’s brittle. More brittle than filament. To counter that you need to use stronger resins or mix in resins. I prefer sirayatech fast abs resin. It’s about three times stronger than the average stuff and costs a little more but worth it. For even more strength you could mix in some tenacious but that stuff is literally double the cost. I’ve cleaned my models in a simple larger Tupperware container filled with IPA with no problems for a few years now changing it out ever so often when it becomes too clouded.
Thanks a ton for the advice! After doing more research it looks like I'll have to move out of a dorm room before I'm able to get a printer due to the fumes. But this was helpful nonetheless!
Did you ever pull the trigger on this? With the Heroscape revival on the horizon, I’m looking into resin printers for the sake rebuilding my collection after I had to sell in 2013.
I did, but I haven't gotten to use it yet. I live in a dorm so finding a spot I can safely set it up is a bit of a challenge. Resin is toxic, which means you don't want to run it in a living space - I think I just found a place I can use it but won't get around to the initial test till next week. Cost-wise, i found a used Anycubic Photon Mono SE for $100 and then I had to buy roughly another $100 of supplies (TREX sent me a list that was super helpful).
Will you be buying/making/using an enclosure or vent hood for your printer? While the printers shouldn't be running in a cramped living space, it's my understanding that proper filtration and ventilation help to reduce harmful particles considerably.
I'm in a two-bedroom apartment and would love to get a 3D printer, but we don't have great ventilation or a "peace of mind" place to set it up. Currently I'm working on a plan for a DIY enclosure involving activated carbon filters, fans, and a HEPA vacuum (with additional carbon filters).
I’m still rocking my anycubic photon original printer. 1 bought it for 170 bucks on a sale, I’ve replaced the screen once for 30 bucks and have printed a few thousand minis. Generally I would recommend any of the anycubic printers up to and including the mono x. You can go bigger or more resolution but in most cases you wouldn’t need to in this hobby. I’ve printed so many minis that I’ve been on a hiatus for a bit because I was out of room to store them and had too many to keep up on painting. As far as resin goes, it’s brittle. More brittle than filament. To counter that you need to use stronger resins or mix in resins. I prefer sirayatech fast abs resin. It’s about three times stronger than the average stuff and costs a little more but worth it. For even more strength you could mix in some tenacious but that stuff is literally double the cost. I’ve cleaned my models in a simple larger Tupperware container filled with IPA with no problems for a few years now changing it out ever so often when it becomes too clouded.
Thanks a ton for the advice! After doing more research it looks like I'll have to move out of a dorm room before I'm able to get a printer due to the fumes. But this was helpful nonetheless!
Did you ever pull the trigger on this? With the Heroscape revival on the horizon, I’m looking into resin printers for the sake rebuilding my collection after I had to sell in 2013.
I did, but I haven't gotten to use it yet. I live in a dorm so finding a spot I can safely set it up is a bit of a challenge. Resin is toxic, which means you don't want to run it in a living space - I think I just found a place I can use it but won't get around to the initial test till next week. Cost-wise, i found a used Anycubic Photon Mono SE for $100 and then I had to buy roughly another $100 of supplies (TREX sent me a list that was super helpful).
Will you be buying/making/using an enclosure or vent hood for your printer? While the printers shouldn't be running in a cramped living space, it's my understanding that proper filtration and ventilation help to reduce harmful particles considerably.
I'm in a two-bedroom apartment and would love to get a 3D printer, but we don't have great ventilation or a "peace of mind" place to set it up. Currently I'm working on a plan for a DIY enclosure involving activated carbon filters, fans, and a HEPA vacuum (with additional carbon filters).
I’m still rocking my anycubic photon original printer. 1 bought it for 170 bucks on a sale, I’ve replaced the screen once for 30 bucks and have printed a few thousand minis. Generally I would recommend any of the anycubic printers up to and including the mono x. You can go bigger or more resolution but in most cases you wouldn’t need to in this hobby. I’ve printed so many minis that I’ve been on a hiatus for a bit because I was out of room to store them and had too many to keep up on painting. As far as resin goes, it’s brittle. More brittle than filament. To counter that you need to use stronger resins or mix in resins. I prefer sirayatech fast abs resin. It’s about three times stronger than the average stuff and costs a little more but worth it. For even more strength you could mix in some tenacious but that stuff is literally double the cost. I’ve cleaned my models in a simple larger Tupperware container filled with IPA with no problems for a few years now changing it out ever so often when it becomes too clouded.
Thanks a ton for the advice! After doing more research it looks like I'll have to move out of a dorm room before I'm able to get a printer due to the fumes. But this was helpful nonetheless!
Did you ever pull the trigger on this? With the Heroscape revival on the horizon, I’m looking into resin printers for the sake rebuilding my collection after I had to sell in 2013.
I did, but I haven't gotten to use it yet. I live in a dorm so finding a spot I can safely set it up is a bit of a challenge. Resin is toxic, which means you don't want to run it in a living space - I think I just found a place I can use it but won't get around to the initial test till next week. Cost-wise, i found a used Anycubic Photon Mono SE for $100 and then I had to buy roughly another $100 of supplies (TREX sent me a list that was super helpful).
Will you be buying/making/using an enclosure or vent hood for your printer? While the printers shouldn't be running in a cramped living space, it's my understanding that proper filtration and ventilation help to reduce harmful particles considerably.
I'm in a two-bedroom apartment and would love to get a 3D printer, but we don't have great ventilation or a "peace of mind" place to set it up. Currently I'm working on a plan for a DIY enclosure involving activated carbon filters, fans, and a HEPA vacuum (with additional carbon filters).
I went ahead and ordered an Anycubic Photon Mono 4K yesterday. I'm sure someone here can chime in and tell me if this is a good idea or not, but I'm not anticipating any prints that will take longer than a few hours, so my plan is to set up as needed in one of my two bathrooms, both of which have exhaust fans that vent to the outside of the house completely, either during the day when the kids are at school, or at night when everyone else is asleep. Obviously the printer won't live in the bathroom, and will be stored away from moisture (and my kids) when not in use. If push comes to shove, I also have a shed in my backyard with electricity that I could probably do a more permanent setup with, but I'm concerned with the ambient air temperatures affecting the printer itself.
I’m still rocking my anycubic photon original printer. 1 bought it for 170 bucks on a sale, I’ve replaced the screen once for 30 bucks and have printed a few thousand minis. Generally I would recommend any of the anycubic printers up to and including the mono x. You can go bigger or more resolution but in most cases you wouldn’t need to in this hobby. I’ve printed so many minis that I’ve been on a hiatus for a bit because I was out of room to store them and had too many to keep up on painting. As far as resin goes, it’s brittle. More brittle than filament. To counter that you need to use stronger resins or mix in resins. I prefer sirayatech fast abs resin. It’s about three times stronger than the average stuff and costs a little more but worth it. For even more strength you could mix in some tenacious but that stuff is literally double the cost. I’ve cleaned my models in a simple larger Tupperware container filled with IPA with no problems for a few years now changing it out ever so often when it becomes too clouded.
Thanks a ton for the advice! After doing more research it looks like I'll have to move out of a dorm room before I'm able to get a printer due to the fumes. But this was helpful nonetheless!
Did you ever pull the trigger on this? With the Heroscape revival on the horizon, I’m looking into resin printers for the sake rebuilding my collection after I had to sell in 2013.
I did, but I haven't gotten to use it yet. I live in a dorm so finding a spot I can safely set it up is a bit of a challenge. Resin is toxic, which means you don't want to run it in a living space - I think I just found a place I can use it but won't get around to the initial test till next week. Cost-wise, i found a used Anycubic Photon Mono SE for $100 and then I had to buy roughly another $100 of supplies (TREX sent me a list that was super helpful).
Will you be buying/making/using an enclosure or vent hood for your printer? While the printers shouldn't be running in a cramped living space, it's my understanding that proper filtration and ventilation help to reduce harmful particles considerably.
I'm in a two-bedroom apartment and would love to get a 3D printer, but we don't have great ventilation or a "peace of mind" place to set it up. Currently I'm working on a plan for a DIY enclosure involving activated carbon filters, fans, and a HEPA vacuum (with additional carbon filters).
I went ahead and ordered an Anycubic Photon Mono 4K yesterday. I'm sure someone here can chime in and tell me if this is a good idea or not, but I'm not anticipating any prints that will take longer than a few hours, so my plan is to set up as needed in one of my two bathrooms, both of which have exhaust fans that vent to the outside of the house completely, either during the day when the kids are at school, or at night when everyone else is asleep. Obviously the printer won't live in the bathroom, and will be stored away from moisture (and my kids) when not in use. If push comes to shove, I also have a shed in my backyard with electricity that I could probably do a more permanent setup with, but I'm concerned with the ambient air temperatures affecting the printer itself.
I’m still rocking my anycubic photon original printer. 1 bought it for 170 bucks on a sale, I’ve replaced the screen once for 30 bucks and have printed a few thousand minis. Generally I would recommend any of the anycubic printers up to and including the mono x. You can go bigger or more resolution but in most cases you wouldn’t need to in this hobby. I’ve printed so many minis that I’ve been on a hiatus for a bit because I was out of room to store them and had too many to keep up on painting. As far as resin goes, it’s brittle. More brittle than filament. To counter that you need to use stronger resins or mix in resins. I prefer sirayatech fast abs resin. It’s about three times stronger than the average stuff and costs a little more but worth it. For even more strength you could mix in some tenacious but that stuff is literally double the cost. I’ve cleaned my models in a simple larger Tupperware container filled with IPA with no problems for a few years now changing it out ever so often when it becomes too clouded.
Thanks a ton for the advice! After doing more research it looks like I'll have to move out of a dorm room before I'm able to get a printer due to the fumes. But this was helpful nonetheless!
Did you ever pull the trigger on this? With the Heroscape revival on the horizon, I’m looking into resin printers for the sake rebuilding my collection after I had to sell in 2013.
I did, but I haven't gotten to use it yet. I live in a dorm so finding a spot I can safely set it up is a bit of a challenge. Resin is toxic, which means you don't want to run it in a living space - I think I just found a place I can use it but won't get around to the initial test till next week. Cost-wise, i found a used Anycubic Photon Mono SE for $100 and then I had to buy roughly another $100 of supplies (TREX sent me a list that was super helpful).
Will you be buying/making/using an enclosure or vent hood for your printer? While the printers shouldn't be running in a cramped living space, it's my understanding that proper filtration and ventilation help to reduce harmful particles considerably.
I'm in a two-bedroom apartment and would love to get a 3D printer, but we don't have great ventilation or a "peace of mind" place to set it up. Currently I'm working on a plan for a DIY enclosure involving activated carbon filters, fans, and a HEPA vacuum (with additional carbon filters).
I went ahead and ordered an Anycubic Photon Mono 4K yesterday. I'm sure someone here can chime in and tell me if this is a good idea or not, but I'm not anticipating any prints that will take longer than a few hours, so my plan is to set up as needed in one of my two bathrooms, both of which have exhaust fans that vent to the outside of the house completely, either during the day when the kids are at school, or at night when everyone else is asleep. Obviously the printer won't live in the bathroom, and will be stored away from moisture (and my kids) when not in use. If push comes to shove, I also have a shed in my backyard with electricity that I could probably do a more permanent setup with, but I'm concerned with the ambient air temperatures affecting the printer itself.
You should be fine running it in a bathroom with an exhaust when no one is around.
There are some resins with strong smell, but I usually use Siraya ABS-like resin, and it doesn't have a strong smell. I've used it in my wide open kitchen, but right now I have it in my large game room upstairs. I don't smell anything, even when I'm in the room until I start cleaning it with alcohol.
In addition, there is not enough information about the vapors. There are short-term risks (that I've never experienced, even when working with the resin). But the long-term risks are unknown due to lack of research.
So it's good to be cautious. But a closed bathroom with an outside exhaust should be good to remove any fumes.
If the smell is too strong for you to work with it during cleaning, then you might want an extra fan near the printer with an exhaust duct running up to the outside vent so that the fumes are pulled right away to the outside vent.
Cost-wise, i found a used Anycubic Photon Mono SE for $100 and then I had to buy roughly another $100 of supplies (TREX sent me a list that was super helpful).
Cost-wise, i found a used Anycubic Photon Mono SE for $100 and then I had to buy roughly another $100 of supplies (TREX sent me a list that was super helpful).
The easiest way to figure out what is needed is YouTube videos. There are many. I believe there's a channel called 3dprinted tabletop with Danny the 3d printing DM. He's good. Also many others. Basically resin printing the figures is the first part, but then tools to post process them are required too. Look up these different parts. Washing resin prints. Removing supports. Curing prints. There's also PPE. Personal protective equipment. Such as goggles, a respirator, and lots and lots of nitrile gloves. You don't want resin on you. Especially your eye. If you do get it on you it's not the end of the world and can be cleaned off, but less is better. The respirator isn't something that's as needed if you aren't around it lots and you have a ventilated area. It's also good to have a way to vent the resin fumes out of the place your printing from. It may not seem like much, but has enough elements to it that it is a whole new hobby. Good luck. If you can manage it, it's a very fun and rewarding hobby, but it isn't easy.
